E-PLUS ION SPA INSTRUCTION

"Providing Safe & Secure Ion Spa Detox Footbath for Our Customers!"

Operating Instruction of e-plus Ion-Spa Device

1. Always fill in health status form before the treatment. (provided by the company)
2. Insert the plug of electrodes to the front panel of the display board.
3. Plug in the cable of transformer to the back panel of display board, whereas the other end of the cable will be plug in to the power supply.
4. Put the electrodes 5-6 cm deep under the water. Please ensure that the central part of the copper plate is covered by water.
   Note: The water level must not exceed over the top of electrodes, or all parts would be corroded and greatly influence the function of the device.
5. Muscle testing is not necessary for ordinary treatment; connect the electricity by switching on the button.
6. Plug the cable of the array into the unit, turn right to lock and left to unlock.
7. Press button ‘OK’ and start to choose the treatment options that are shown on the screen, press [+] or [-] to adjust an appropriate options for treatment. There are 5 different treatment options. (Option 3 is commonly used by normal user)
8. After choosing the option, soak feet in the water, then press button ‘OK’ and set the time duration for treatment. The time setting can be adjusted by pressing [+] or [-].
9. Press OK to confirm, and press START to run the cleansing process
10. Panel display (A) ampere 0.10 - 1.00, add a bit of salt into the water until (A) ampere become 1.7-2.1
    The quality of water varies in different places. (A) ampere is capable of measuring the residue and conductivity of the water, if the water is over (A) ampere 1.00, please replace with water processed by carbonization/fibre filters.
11. There is always some information displayed after each foot bath.
12. The electrode plate must be disinfected by washing with hot water, bleach or cleaner after each treatment.

Instructions for new Array (Use first time 'without feet'):

1) Use a small plastic container, add warm water and put in new Array. Water should be at the screw level without feet.

2) Add a tea spoon of laundry or washing powder into the warm water. Add salt until the Ampere (A) reaches 2.2 to 2.3.

3) Use Mode 2 (all negative) and run for 30 minutes 'without feet'.

Note: The above is to get rid of the rust proof layer protecting the metal Array.

Please follow the above instructions for all new Arrays and you will get good result on the subsequent therapies with feet.

Mode selection

Although there are 5 treatment options, we suggest choosing option 3, 4 ,5 mode.

1. 100+ can only be used for clinical test. (use only after consulted the doctor)
2. 100- can only be used for clinical test. (use only after consulted the doctor)
   Either 100+ or 100- will cause imbalance in pH level.
3. 70+ (positive charged)/ 30- (negative charged), this setting can be used by anyone. (weaker )
4. 15+ (positive charged)/10-(negative charged) /5+ (positive charged) (moderate)
5. 10- (negative charged)/15+(positive charged) /5- (negative charged) (stronger)
6. From thousands cases of experiments that had been conducted, users who get the result of positive from muscle testing should choose 4, and alternatively, choose 5.

Rules of Usage

1. Always fill in health status form before the treatment. (provided by the company)
2. Only two legs are allowed throughout the whole process of the treatment.
3. Water can only be used once.
4. The duration of each treatment must not be more than 30 minutes.
5. children over the age of 5 may take the treatment under the accompany and supervision of the parents. The duration should be 15-20 minutes.
6. People below the age of 50 may use once every two days. A break of 3 weeks after every consecutive 14 treatments.
7. People above the age of 50 may use once every three days. A break of 2 weeks after every consecutive 14 treatments.
8. During the foot bath, remove the legs should you feel uncomfortable, and off the unit instantly.
   (Then try with a weaker mode within 24 hours)
9. Adopt a surge-protector during storm or unfavorable weather.
10. Do not let the person have close contacts with those whom are not undergoing the session.
11. Do not sit on metalic seat.
12. Remove metal items like watches, coins, glasses and necklaces etc.
13. Do not use RO water, distilled water and processed water.
    (water processed by normal fibre /carbonization filter is recommended)
14. Always off the power supply when the unit is not in use.

Recommended schedule and functions

Maintenance and Repairing

1. The surface of the electrodes will become smooth after the ion-cleansing. Fill in about 1000ml of water and a tea spoon of white acidic powder, let it soaks until the next morning. Clean the machine after 5-10 times usages.
2. Electrode is a depleting material, and the depletion rate depends on the physical health condition of the users and the frequency of usage.
3. If you encounter any other problems when using this device, please ask for assistance from the agents and manufacturer.